Where Are the Luxury Linens?

I Want Bamboo Sheets!

Menu Close

Tag: how to remove a fiberglass bathtub and surround

How to Remove a Fiberglass Bathtub and Surround — by Home Repair Tutor

How do you remove a bathtub and a fiberglassshower border? In this video, my sidekick, Steve White, fromSRW Contracting, is going to show you step by step how to do this. And in the end, weve got an awesome surprisefor you, courtesy of DeWalt. So learn Steves talents in this video, andin the end check out the astonish that we have in store for you, all right? Let jump into the tutorial right now. Were going to go ahead and get this fiberglassunit out and set up the onepiece fiberglass unit which was installed before the framingof the lavatory weve throw in. So theres no way to get this out in onepiece. And it would be pretty tough to get down thesteps and everything else, too.So the first thing I do is turn off the waterand take out the fragments off. Each one is a little bit different. So Im going to have to check out whatsneeded. And this one simply threads out. Then I have two fucks set up over here. Take the administer off. Take the two fastens off the trim. Take the shower head off. Okay, and then sometimes you get the showerarm out of the wall with a screwdriver in the end. Just wind it out. It gives people a bit of the leverage. So, and you usually want to try to make thedrain assembly apart so that when youre pulling out the tub, youre not destroyingany plumbing underneath.Sometimes this can be tricky if its prettyold. Sometimes some of this nonsense doesnt wantto thread out. And theres not much you can do about that. Sometimes I just take a grinder and end upcutting the tub area out around it precisely to make sure that you dont have a problem. If you have access behind it, you can takethe drain assembly apart behind it sometimes.But more seasons in life youre going to beable to get this unthreaded. Sometimes that little removable tool for thedrain assembly is with a tube wrench. Pays you all of the leveraging to change itout. So this freighter piping, I cant get out. So Im just going to use my grinder andjust cut off the pipe. It doesnt have to be quite. Okay, then you can see actually it has a tilesurroundedtub. So Im going to remove parts of that first. Okay, so now you got that all kind of exposedall the way around the tub. Okay so theres a little flange that thatdrywall sits down onto. And that goes all the way around this tubas well. Now if I were obstructing this bumpout of wall, I would saw this all down along the two sides of the tub as well to cut this flange becausethe flange goes all the way down here. Well Im not continuing this corner, so itdoesnt actually matter because Im turning this into a walkin shower.So I dont have to worry about put thisdrywall angle. And honestly, even on the other side, I woulddo the same thing if I were hindering the drywall, but Im redrywalling the chamber. So that wont actually difficulty either. So its really just as simple as gettinga encountered is all. I use like a wood/ metal blade. Multipurpose. I frequently just go with something What is this? Like 6, 8? Oh, this is 9. So its something not extremely, too long or itsall going to be bind up or whatnot. But always shut the irrigate off because younever know exactly how the plumbings done until you get into this. Ive seen it where sometimes even waterlines are behind the tub, feeding it. So running the saw along the region, you canpotentially trimmed that. So shut the spray off before you even do this. And you are well aware, just were pluming the walkinshower, any plumbing that it is possible existing there over place.So Im going to show you how much an areathere is behind it. Thats why sometimes plumbers only extended alltheir substance kind of loose behind the tub because there is space there. So as simple as sawing the area. Like I said, I dont actually care about thatcorner. When I use that Sawzall, I always kind ofangle it down a little bit because you can see how theres cables in that wall. You dont want to have it too far in a wallwhere you might chipped the wires. So I always kind of angle the Sawzall downa little bit. So now we got the drain assembly out and stufflike that.We can just simply pull out the tub. So this is kind of a perfect precedent of whatyou might run into when “youre trying to” do a tub conversion to a walkin shower. You can be found in the vent load thats insidethe shower arena where the tub was able to cover that area. So were going to have to reroute the ventstack to be inside the wall and run through.So thats actually an excellent example of whatyou might run into when you remove the tub. All right, I hope that was helpful. I make, theres truly nothing jolly aboutdemo, but you just really have to muscle through it and use a Sawzall and work through it. Again, thats why I actually enjoy thatwhy let me say that again. And thats another reason why its bestto kind of demo everything. The more epoch that you have to kind of considerdrywall areas and trying to pull things out, the longer its going to take reallyto do everything because, fortunes are, when youre turn to a walkin shower, youregoing to be able to make that a little bigger to be able to finish the drywall alot nicer. In this bathroom alone, were already takingout the reflect, were rerouting the plumbing for the submerges, were rerouting this forthe shower. It certainly sees no smell just to leave threepieces of drywall to stay in now to finish. So make everything down with the saw, andstart from scratch.It realizes it a good deal easier. So hopefully it was helpful. Thanks. Well there you have it. Thats how you remove a bathtub and a fiberglassshower environment. If youre doing a bathroom remodel project, these the expertise and tips can really come in handy. And expressed appreciation for, Steve, for showing us how todo it. So here is the surprise. DeWalt is partnering with us, and theyreproviding a brand new 20 V Max lithiumion reciprocating saw. So theyre going to give away one with uson Home Repair Tutor. So go to HomeRepairTutor.com, check out thelatest tutorial, and youll be seen to what extent one random, lucky person is going to win thisreciprocating saw. Its phenomenal. Its a implement that comes in handy wheneveryoure doing a fiberglass shower circumvent demo activity or removing ornaments, you need areciprocating saw, and you need one that is strong. And the 20 V Max reciprocating saw by DeWaltis fantastic. So I to be expected that you liked this video today. Again, check out the giveaway back on overat HomeRepairTutor.com.And for all DeWalts latest implements that arecoming out, you can go to DeWalt.com as well. Thanks for watching. Take care, and well see you in the nextvideo ..

How to Remove a Fiberglass Bathtub and Surround — by Home Repair Tutor

How do you eliminate a bathtub and a fiberglassshower encompass? On this video, my friend, Steve White, fromSRW Contracting, is going to exhibit you step-by-step how to do that. And ultimately, weve received an splendid surprisefor you, courtesy of DeWalt. So learn Steves abilities on this video, andin the top verify out the surprise that we have in store for you, all right? Lets leap into the tutorial right now. Have been going to go forward and get this fiberglassunit out and installed the one-piece fiberglass unit which was established earlier than the framingof the lavatory weve put in.So theres no technique to get this out in onepiece. And it will be pretty rough to get down thesteps and the whole lot else, too. So the very first thing I do is flip off the waterand take out the portions off. Every one is a little bit bit special. So Im going to have got to investigate out whatsneeded. And this one simply threads out. Then i have two screws set up over here. Take the handle off. Take the two screws off the trim. Take the shower head off. Ok, after which regularly you get the showerarm out of the wall with a screwdriver finally. Just wind it out. It gives you a bit of of the leverage. So, and also you probably need to check out to take thedrain meeting apart so that when youre pulling out the tub, youre now not destroyingany plumbing beneath.Commonly this will also be tricky if its prettyold. Many times some of these things doesnt wantto thread out. And theres no longer much you are able to do about that. Frequently I simply take a grinder and finish upcutting the bathtub field out round it simply to be certain that you simply dont have a hindrance. In case you have entry behind it, that you could takethe drain meeting apart at the back of it commonly. But extra occasions in existence youre going to beable to get this unthreaded.Sometimes that little removable software for thedrain assembly is with a pipe wrench. Offers you all the leverage to curve itout. So this bottom pipe, I cant get out. So Im just going to use my grinder andjust reduce off the pipe. It doesnt have got to be pretty. K, then one can find truly it has a tile-surroundedtub. So Im going to get rid of components of that first. K, so now you obtained that each one style of exposedall the way in which across the bathtub. Ok so theres slightly flange that thatdrywall sits down onto. And that goes all the means round this tubas well. Now if I had been keeping this bump-out of wall,i might saw this all down alongside the side of the tub as well to cut this flange becausethe flange goes all of the method down here. Good Im not retaining this nook, so itdoesnt rather subject since Im turning this right into a stroll-in bathe. So I dont have got to worry about retaining thisdrywall nook. And truthfully, even on the other aspect, I woulddo the identical thing if I were preserving the drywall, however Im re-drywalling the room.So that wont fairly topic both. So its particularly just so simple as gettinga saw is all. I exploit like a timber/metallic blade. Multipurpose. I often simply go along with something What is that this? Like 6, eight? Oh, this is 9. So its whatever not too, too lengthy or itsall going to be bind up or whatnot. However continually shut the water off since younever know precisely how the plumbings executed unless you get into this.Ive obvious it where frequently even waterlines are at the back of the bathtub, feeding it. So walking the saw along the nook, you canpotentially reduce that. So shut the water off before you even do that. And you already know, simply were pluming the stroll-inshower, any plumbing that possibly present there over place. So Im going to show you ways so much an areathere is in the back of it.Thats why frequently plumbers simply run alltheir stuff type of loose behind the bathtub in view that there may be area there. So so simple as sawing the nook. Like I mentioned, I dont fairly care about thatcorner. After I use that Sawzall, I consistently type ofangle it down a bit bit in view that you can find how theres wires in that wall. You dont need to have it too far in a wallwhere you might reduce the wires. So I continually style of attitude the Sawzall downa little bit. So now we bought the drain meeting out and stufflike that. We are able to just quite simply pull out the bathtub. So that is style of a ideal instance of whatyou could run into whilst you try to do a bath conversion to a stroll-in shower. You will see that the vent stack thats insidethe bathe field where the bathtub was capable to duvet that field.So had been going to ought to reroute the ventstack to be throughout the wall and run through. So thats truely a primary illustration of whatyou would run into when you get rid of the bathtub. All correct, i’m hoping that was worthwhile. I mean, theres relatively nothing pretty aboutdemo, however you simply rather have got to muscle via it and use a Sawzall and run by means of it. Once more, thats why I particularly enjoy thatwhy let me say that once more. And thats another motive why its bestto variety of demo the whole lot. The extra time that you must style of considerdrywall corners and looking to pull matters out, the longer its going to take reallyto do the whole lot on account that, possibilities are, when youre converting to a walk-in bathe , youregoing to be ready to make that a bit bit higher to be competent to finish the drywall alot nicer.In this toilet alone, had been already takingout the replicate, have been rerouting the plumbing for the sinks, had been rerouting this forthe bathe. It relatively makes no sense simply to depart threepieces of drywall left in here to finish. So take the whole thing down with the saw, andstart from scratch. It makes it quite a bit easier. So expectantly it was invaluable. Thanks. Well there you’ve got it. Thats how you remove a bathtub and a fiberglassshower encompass. If youre doing a rest room reworking challenge,these competencies and pointers can relatively come in helpful. And thanks, Steve, for showing us how todo it. So right here is the surprise. DeWalt is partnering with us, and theyreproviding a manufacturer new 20V Max lithium-ion reciprocating saw. So theyre going to provide away one with uson dwelling repair Tutor. So go to HomeRepairTutor.Com, examine out thelatest tutorial, and youll see how one random, lucky man or woman goes to win thisreciprocating saw. Its excellent. Its a tool that comes in handy wheneveryoure doing a fiberglass bathe surround demo venture or putting off studs, you need areciprocating noticed, and also you want one that’s powerful.And the 20V Max reciprocating noticed with the aid of DeWaltis terrific. So i am hoping that you liked this video at present. Once more, examine out the giveaway back on overat HomeRepairTutor.Com. And for all DeWalts today’s tools that arecoming out, that you could go to DeWalt.Com as good. Thanks for staring at. Take care, and good see you within the nextvideo..

© 2020 Where Are the Luxury Linens?. All rights reserved.

Theme by Anders Norén.