In our prior video we showed you easy methods to putup the drywall and to water resistant it making use of KERDI membrane for the Schluter bathe method.Now in this video, were going to exhibit you set up the Schluter bathe pan. Thisis, once more, very simple, and had been going to stroll you through it step-with the aid of-step.All proper, so the shower drain, have been going to ought to reduce this out in an effort to get tothe drain unless you will have access below. So well attempt to find the joists. Good juststraighten this out a little. So we simply measure beneath the plywood except we hit the joist.So we received like eleven inches, so well go eleven .The rationale for the eleven is given that the joist is 1 extensive.So basically all Im trying to do is cut on that joist so that once I reduce this outI can comfortably slot in a new piece of plywood. And then well just reduce this.For the primary cut, we used a Sawzall. So have been just utilising the Milwaukee super Sawzall tocut via the prevailing inch OSB thats in the shower.So we desired to cut along thejoist, proper within the center of it so that once we take this wood out well be in a position to addanother piece of timber down over prime of the center of those joists. Then we just useda circular saw to make a straighter reduce. So on this case we received thus far, and then we couldntgo any further, after which we had to use the tremendous Sawzall to make the rest of the reduce.Essentially, you would use a Sawzall to make all these cuts. And then we just used a hammerto pry up the loose OSB. This is a little bit of an unusual concern,however you clearly have a entice catecorner to the drain area. They put a straight 45connection right here, and Im now not certain precisely why they introduced the plumbing over this fashion.But sincerely what have been going to do is just essentially reduce off our existing drainhere and extend this drain over into the core of the bathe.To reroute this is gettinginto rather a little of additional work. And so the whole lot is mostly executed to code, itsjust a topic of finagling this to our new drain location.We effortlessly used a Sawzall to reduce the straight run of the pipe right below the drain.Okay, so for your Schluter drain, this may increasingly appear like packaging in the field, but this isactually made to our reason to slip onto your drain. And this may occasionally in actual fact set thedrain on the right peak that you just want it. So dont throw them away, and use them.And basically good just sit down this right here, and that style of dictates the peak thatwe want it.Two-inch deck screws were used to screw throughthe OSB and into the 2×4 beneath it. And then well get some bigger deck screwsinto the foremost joist here. So we used 3-inch deck screws to toe screwinto the foremost joist. These 2x4s, now discover how we use a liquid nail on them as good.So had been simply utilizing a hammer here to pound that 2×4 down and over. The liquid nail willsecure it to the backside of the OSB. And on the other hand, had been using these 2-inch deck screwsdown through the OSB and 3-inch deck screws to toe screw them into the present joist.Here have been simply adding somewhat 2×4 to the edge of the OSB. And the reason why weredoing this is the new OSB or plywood that wishes to be put down for the Schluter showerdrain desires to be thoroughly supported. So thats why had been adding all these screws.Have been getting a measurement right here for the brand new OSB. Have been just going to reduce that tosize and fit it, so that after had been able to reduce the gap in it for the drain, wellhave it at our disposal.Okay, so we wish to 16. Three and a half.The maximum diameter of the gap is 5 inches. It cannot be any larger than that. You donthave to make use of a hole noticed. A jigsaw will also be used.Right here were simply making certain that the drain is really established on the shower. And thenwe marked the region of the drain down beneath onto this air duct. As you’ll find right here, wedrilled a pilot hole by means of that and then a greater holea 2 holethrough itso that we are able to entry our pipe from down below. This isn’t excellent, however its whatever thatwe had to do. And this is often why that joist used to be notched out.Then liquid nail was applied over high of our 2x material, and were going to set ournew OSB over prime of that. So were going to glue and screw the new OSB in this region.So as you will see that here, were simply hammering it into situation. After which had been going to usethe identical 2 deck screws that we used for the historical OSB that we screwed right down to thenew 2×4.So on this precise predicament, that is justa commonplace drain. What have been going to do is just glue our riser pipe up and let ithang down wildly down below. And good cut to connect the brand new P-trap beneath. Butwith this scenario with the duct work where you cant see this drain, its going tobe less difficult simply to have a good wild piece of riser pipe come up. After which good connectthat afterwards underneath. With ABS, its quite predominant to applythe ABS cement to each the hub of the drain and the pipe itself and hold it in location forseveral seconds. Okay, since have been going to be simply mixinga half of a bag, had been still going to make it at the wetter ratio for membranes and settingthe bathe pan.So had been going to make use of four quarts of water for half of a bag.We totally recommend making use of Schluters ALL-SET for this and mixing it in line with the recommendations.With the aid of utilizing ALL-SET, youre going to keep the Schluter warranty.Combine for 5 minutes. Its important to combine ALL-SET to the rightconsistency and per the instructions. We were also testing DeWalts new FlexVolt mud mixer,and it labored relatively good. We cleaned off the top of the subfloor inthe bathe areathats also primary so that you dont have any particles interferingwith the pan. Ok, so one of the vital exceptional matters about thesepans is they’ve some pre-markers here for the distinct size showers which are sort oftypical.This is a 60 x 38 pan, and i will reduce this right down to truly any sizethat i need. Undoubtedly this is a core drain location. However my first marker right here that theyhave depicted on the back, in the event you cut this and the opposite aspect, it will be a 54pan;that is for 48. Now with my drywall set up in my bathe, were at forty seven. So I basicallyhave to cut a 1/2 inch off of this line. I will be able to just reference this line and cut a halfinch off to get my 47. After which the identical with this side.Now, you want to pay awareness to the place your drain is located before you go cutting this.One thing about the Schluter method: its very forgiving for those who mess up.Say if youcut this thing an inch off for any cause, that you may simply simply p.C. The corners withthinset or mud to fill in the areas. So if you happen to reduce things off slightly bit, its notthe end of the world. That you could nonetheless use the pan and get this factor water-proof. You canalways measure from your middle of your drain and make sure that the whole thing works correctly.Now, we established that drain, so i do know that I just need to get a forty seven total width.And good double-determine ourselves right here. Thats about 47 inches.All proper, so good just use a new blade on a utility knife and just reduce the pan.This is the high-quality factor concerning the Schluter shower tray.Its produced from gentle-weightexpanded polystyrene, which is robust, but you need to use a utility knife to reduce throughthe pan and reduce it to dimension. So as you will see here, it doesnt take very lengthy to dothat. And what we like first-rate is that they’ve the templates on the again of these new showertrays as a way to see precisely the strains that you just have to cut when you have a commonsize tray. After which as far as the width, these pre-markerson right here is for a 32-inch pan, and that what we want to go with.So have been goingto use the instructional materials that it already has for a 32-inch pan.So again, we simply reduce this shower pan to measurement in terms of the width and length. And youcan do the certain identical thing. So we reduce this 60 x 38 bathe trayinto the size that we needed for the small shower remodel. So again, theres a lotof customization that you would do with the Schluter bathe trays, so preserve that in mind.So here were just dry-fitting it to be certain that it does match adequately. And if weneeded to cut something down, we would. However we now have a quite exceptional, tight match towards theKERDI membrane.After which we brought the froth insert for the drain, and we dry-match the drainas good to be certain that it used to be going to fit the right method.K, so as youre dry-fitting it, just double-verify to see if this drains goingto take a seat stage considering the fact that this is lovely predominant to make everything sit down stage. So just putyour little yellow torpedo level on right here. And also you would see how so much room you will have asfar as play. If you want a little bit bit of adjustment, you’ve got a excellent all of the means around tomove this round. Good definitely, you just make certain that that is middle after we getto set this. But the way that were doing this, having this riser, considering the fact that we have theability to attach the plumbing under, had been going to set the pan and the whole thing firstand then set the drain. Now when you didnt have that and also you wanted to set the drainfirst and attach the plumbing, you could need to take these little core pieces outand thinset them into location around the drain.And in order to provide the appropriate height of thisdrain to the pan approach. So in case you have entry beneath, you might dosomething like this. Connect the whole thing later. And if now not, youre going to need to havethis drain set first and then the pan. K, first thing before you place the pan isto wipe down your substrate with a damp sponge. Get any dust off of there.And this helpskeep that subfloor from drying out the thinset too quick.To use the pan with the thinset, you need to make use of a x three/8 notch trowel. So youregoing to need a better trowel to set this pan. You must backside your trowel firstand burn it into the substrate. And then directional troweling from there.And for these components, we just have got to embed this into our thinset. All correct, and thenwe must get some thinset around the drain. I used my 6-inch knife to do this. And thenjust do a twisting movement to get that set into place. Also, use your level to make sureits sitting quality and stage. After which because you have got come action, you would want tojust measure to ensure that is sitting excellent and core.After which practice a little bit bitmore thinset around the drain. Use a KERDI trowel to trowel it out. And then it comeswith this little fleece to adhere to the drain. Its valuable to ensure that this fleeceis as flush as feasible with the fleece thats already on the Schluter bathe tray. So asyou can see here, the thinset was blended to the correct consistency, and have been removingany of the surplus thinset that oozes out between that fleece and the drain assembly and theshower tray. And had been sponging down any excess thinset as good. So again, thatsreally essential. So that you just mounted that fleece round theflange. So the fundamental section is that this fleece making a excellent connection to the drainbecause this fleece is bonding to the flange and the pan itself. So simply be certain thatthis isnt overhanging and is simply bonding to the flange.All right, now we measure our curb. Wellbutt proper up to it. So 47 inches. Forty-seven inches.A pace rectangular used to be used to ensure that the pencil marks have been equidistant from theedge of the Schluter bathe curb. After which we just used a utility knife to cut this curbto size. Again, just use your utility knife to cutthis. The satisfactory factor about the new Schluter showercurb is that it already has the fleece on prime. So when youre slicing it to dimension andyoure putting in it, theres no must put any extra fleece over prime of thecurb. The historic curbs have been just foam and you then must add the KERDI membrane over topof it.But now that the KERDI membrane is already embedded into the curb, it reallyspeeds up the installation really somewhat. It also reduces the facets of failure.Right here we just slicing the support using a Sawzall. Given that Im looking to maintain all this tile underneathit here, Im going to have to cut this change in peak. So we acquired basically an inch thatwe have to cut off of the bottom of this. To trim down this curb, we made two markson each and every finish, and we notched out the curb utilizing a utility knife after which snapped a chalk lineacross the size. That is relatively one of the most easiest things to do for not only a curb butfor most often any backer board, is snapping a chalk line. Then we used a utility knifeto cut out the part of the curb that we needed to remove.So remember, had been goingto be setting this curb down into that crevice between the Schluter shower tray and the existingtile in this bathroom. So thats probably the most explanations why had been slicing it down tosize. Im also going to must reduce some of thisout. All correct, so we ought to make that basicallytwo inches.So we clearly must cut out this much of our blocks.Utilising an oscillating multi-device, just like the Fein MultiMaster, makes this so much less complicated.Obviously, its just foam, and you should utilize a utility knife. However you could also controlthe depth of the reduce quite with ease using an oscillating multi-tool. And it simply speedsup the whole approach, which, speed as you understand, is quite foremost when youre installinga bathe considering there are such a lot of exclusive elements to it. If that you can velocity up the processin any approach, shape, or type of the software, its certainly valued at the investment.So we decrease all these support blocks within the curb, after which we dry match it to make surethat it would fit in between the shower tray and the existing tile flooring.So Im environment this in a technique so one can enable this to drain closer to the bathe here as well.It doesnt need to be much, but its bought to be some thing to empty.In view that Im adjustcutting this, if youre no longer adjusting the cut, then that is simply going to be squareand straight, after which youll must pitch your tile to make it work. However on account that I havethe ability of being capable to slope this, I could as good go forward and try this withthe curb. So you additionally wish to get some thinset againstyour pan to bond to it. The x 3/8 square notch trowel isused to use Schluters ALL-SET to the brink of the shower tray. And having that mortaron the brink competently helps and bonds the Schluter bathe curb to the tray.And then you want to put some on the aspect of your KERDI so it bonds with the edges ofthe partitions as well. Okay, after which on the other part of the curb,we want to put some KERDI-repair to adhere this to the external flooring.KERDI-repair will make certain that the curb is safely bonded to that tile flooring outsidethe bathe.So keep in mind, on this special transform, we did not cast off the ground tile.So we kept the whole thing in place. And having the KERDI-repair allowed us to thoroughly bondthe curb to the existing tile ground. Now what have been doing is simply smoothing outany thinset that oozed out between the curb and the shower tray on account that had been goingto be bonding KERDI-BAND and the inside and external corners between the curb and the showertray.So here again had been just cleansing up a bit bit earlier than we begin the processof completely waterproofing the curb. You surely need to make certain youre levelhorizontally, too. Had been pre-slicing all of the KERDI-BAND, andwe particularly suggest that you try this in view that it simply makes the system so much less difficult.So without doubt, you need two portions of KERDI-BAND for the width and two portions of KERDI-BANDfor the length that goes on the again wall and between the curb and the shower tray.So again, were making use of Schluters ALL-SET thinset mortar to the corners here. So thefirst step on this process is to use thinset both on the two walls and the bathe trayin the corner. So you have got three special planes that must be waterproofed. You havethe wall, in this case, the curb, and the shower tray. The shower tray, the curb, andthe wall on the other inside of nook.After which on the back half of the bathe you might have thetwo walls and the shower tray. What have been doing here is applying a pre-formedSchluter within corner. Now these come with both the drain or the bathe tray. And sowhat you need to do is put these within the corner and be certain that its as flush with theshower tray and the two walls as viable. Its rather major to get rid of all excessthinset between this within corner and the walls and the tray in order that your tile isntaffected. The principal a part of these corners is justto get them tight into the corner. You dont wish to have so much crammed up. Thats whyusing the right trowel, its fundamental to use the KERDI trowel. Its going to havethat minimal amount that is required to make this water-proof. And then also mixing yourthinset to the suitable consistency will be certain that this build up could be very minimal. Soif you end up having a tough time with the thinset where its no longer going to be realthin and tender, then you definately might wish to remix some more thinset to make it a little bitlooser and get this tighter in the corners.So well with the entire corners first.So like Steve simply mentioned, we began with all of the corners with the shower tray set up.You need to get all the corners in place earlier than you move on to whatever else. Corners arethe most important a part of any bathe that would potentially leak. And at the drain as well. But in particularbecause it is a very, very small bathe, the corners are kind of the vulnerable points. Sowe put in all the corners, these four pre-formed inside corners go in first. Again, you wantto dispose of as so much of the thinset mortar as viable so that those corners sit flush andflat in the case of the shower tray, the curb, and the partitions. And the purpose why is if youvegot a little bit bit of a hump or a bump between the within nook and the skin of the tray,the curb, or the wall, its rather going to be difficult to make that up in phrases of tiling.Now, you are able to do it via again buttering or back troweling the tiles. However mostly it canbe complicated if youve bought small tiles like we are going to have in this shower tray.So were going to be putting in penny tiles, and we desired to ensure that the cornersand the KERDI-BAND have been as flat as feasible with regards to all of the surfaces.Now what have been doing is applying with the notched part of the KERDI trowel thinset tothe bathe tray, and to the curb, and also to the partitions.So the purpose why had been doingthis is had been going to be bonding KERDI-BAND in any respect these intersections in view that the KERDI-BANDis going to go over top of the inside corners and over top of the bathe tray and the wallsand the curb, and its going to water-proof this Schluter shower tray. Now you want todirectionally trowel the thinset mortar such that all the notches face the same path,proper? So that when the KERDI-BAND is bonded to the highest of the thinset and compressed usingthe 6 drywall knife, all of the air will cave in out of the ridges and out from between theKERDI-BAND and the thinset mortar. Directional troweling helps get rid of air pockets andpossible leak features on the KERDI-BAND. So its relatively, fairly central that youdo the directional troweling. So were beginning with the back wall. Itdoesnt rather topic which wall you with, but we started with the again wall.Thenwe applied KERDI-BAND between the bathe tray and the curb. After which from there, we smoothout the thinset between the KERDI-BAND and the wall and the shower tray and the curb.Now, one factor of observe is when the KERDI-BAND is ready over top of the wall and the showertray or the curb and the shower tray, it will have to be set equidistant. That means you’ve the sameamount of KERDI-BAND on the wall as you do on the tray. So the few inches that you just haveon the tray should equal the few inches that you’ve got on the wall or the curb.So again,the KERDI-BAND will have to be set equidistantly. And then you definitely must put off any of the excessthinset mortar that’s between the KERDI-BAND and the curb, and the KERDI-BAND and the showertray. And the identical thing goes for the walls. This takes a little bit of time, however the theorybehind all that is that the thinset mortar, because it begins to established, the crystals actuallystart to grow roots in between the KERDI-BAND and the shower tray and the walls. And thoseroots are so powerful that it also prevents water from being depraved down into the differenttransitions. So thats the reason why we use thinset mortar.So you wish to have to have these pieces as whilst possible. The thought is that the whole thing thatoverlaps to overlap through 2 inches. So when youre putting this in, simply ensure that you just have2 inches of protection on every perspective, together with 2 inches that go over the corner, 2 inchesthat go up the wall.So at any place that you just follow the KERDI-BAND, you want to have 2 inchesof insurance policy onto something waterproofing seam that youre trying to accomplish.And undoubtedly you could have thinset underneath. Theres 2 inches as good. So something youretrying to overlap, make sure that theres a layer of thinset.So now were going to conclude off the KERDI-BAND set up by means of including KERDI-BAND to the plumbingwall and the wall reverse that. So once more, were just utilizing the same methodology thatwe used for the curb and the primary wall.Had been just making use of the KERDI-BAND and smoothingit out as much as feasible. So youve bought overlap with this KERDI-BAND piece, and theKERDI-BAND piece on the curb and the back wall, as good as the corner pre-shaped portions.So theres overlap. And thats why you wish to have these pieces of KERDI-BAND to be as smoothand as flat as viable. Take a sponge and simply wipe down everythingsmooth to be certain that you dont have any humps. And then lets put our outsidecorners.So two outside corners are indispensable for thisinstallation given that of the curb. The curb is assembly up with the wall, so that you want twooutside corners: one for the left aspect, and one for the proper part. And this may increasingly overlapthe KERDI-BAND thats both on the wall and the curb. And the reason why you want thisis for the reason that there was once no KERDI-BAND that used to be placed on the highest of the curb between the curband the partitions. So these additionally come with your drain or your Schluter bathe package. So yougot to position thinset underneath this external nook and gentle it out once more as so much aspossible. Now, these corners can frequently tent up.Its very difficult to look probably within the video. But when youve worked with these outsidecorners earlier than, commonly they tent up if theyre a bit bit too lengthy on one facet.So what you are able to do, as long as you may have the two-inch overlap, is you could trim down theseoutside corners.However again, you simply must have that 2-inch overlap between theseoutside corners and some other KERDI-BAND that was applied between the wall and the curbor the bathe tray. So which you could reduce these outside corners. Its only a subject of havingthat 2-inch overlap that Schluter wishes for the motive of waterproofing. So thatswhat we did there. We sincerely cut that corner with a utility knife.And we also must point out that it doesnt hurt to have a pair of scissors. Scissors,they obviously are available helpful when slicing down these within or external corners and theKERDI-BAND. You dont ought to use a utility knife always.You could reduce proper throughit with scissors. So as you saw there, we scale down the insideportion of that external corner that used to be going within the shower so it will match properlyin terms of the peak differential between the curb prime and the shower tray. But againwere simply smoothing down these outside corners so that not one of the thinset and thecorner itself intervene with our tile work in a while.K, so in your drain shower kit, itll include three distinct sections: the actualfinish drain strainer, this little collar that adjusts into the drain, after which thislittle flange that you just thinset in. So that you simply effectively put this flange round this sleeve.So theres a couple of indentations on this which have little stubs on the one side. Youwant to press this into it truly clamps into the brink of this. So as you might seeon the facet of the drain it has like somewhat indentation; it type of flares out.So theselittle indentations on here is what sort of holds the drain into situation. So it just snapsin. And i’d endorse when youre tiling to take the actual drain strainer off becauseyou dont need to get a entire bunch of thinset all smooched in this. Itll be really difficultto smooth everything out. So simply take the specific strainer off.So then the thought of that is to regulate your strainer to the tile depth that you’ve got.So you might have various room here.You have just about typically virtually an inch of room. So if youvegot some relatively thick tile, this will modify from side to side. But in actual fact, the inspiration isonce you get the tile in right here, which you can press this right down to the level of your tile. So itsa excellent suggestion to take a look at to get quite close so youre now not spending an excessive amount of time pressingit down. That is our tile here. Were making use of a pennytile. So Im simply going to maintain it so its just pretty a ways above of presses down afterI have the tile set.But what you wish to have to do is thinset this in location since this littlecollar right here is meant to embed into thinset. So embed thinset round this. And you alsowant to getthis is an foremost detailyou definitely wish to get some thinset on thecorners of this strainer. And this is going to support support. Whilst you press this down,itll have some thinset underneath of it to have support. So put a little bit of thinsetat each and every corner. And then youll embed this into our thinset. And then for now welljust, whilst have been doing the design, well simply get rid of this thinset; tender it out.Seeing that were making use of penny tile, we dont have any reference, have been just going touse this for reference.This 2-foot stage is put up towards the drain,and we measured off of the entrance wall in two extraordinary locations to make sure that thedrain was once pleasant and square with the entrance wall and the back wall.So I feel that makes it straight. And then, it has a bit brand on here.So Im simply going to be certain after I put this on here Im capable to have the identify.Schluter shower trays and curbs are very versatile. As you noticed, that you would be able to cut them to measurement justusing a utility knife. The next move on this bathe installationwas to tile the shower pan and the wall. So if youre doing a customized-tiled bathe andyou wanted help with that, without doubt verify out bathroomrepairtutor.Com. Thats wherewe have our video library with over 200 additional video tutorials that walk you by means of everythingstep-via-step for a customized toilet or shower installation. So ensure you visit bathroomrepairtutor.Com.You wont be dissatisfied.Thanks for staring at this video, and wellsee you in the next one. Take care!.